Experimental and numerical analysis of the impact of a liquid flow rate on the operational performance of a cross-flow tube-and-fin heat exchanger
DOI:
https://doi.org/10.24425/ather.2023.149721Abstract
The paper is dedicated to an issue of the influence of a nonuniform flow of mediums in a cross-flow water-air heat exchanger, the core of which is a bundle of elliptical finned tubes. The main purpose of the work is to determine the impact of non-uniform water inflow for various mass flow rates on the thermal efficiency of the heat exchanger. Multivariate analyses were carried out for various temperatures of water, and for measured nonuniform air distribution at the heat exchanger input. Two variants of water distribution were considered: non-uniform water distribution assumed considering a non-uniform air inflow and water distribution resulting from hydraulic resistances calculated for different locations of water inlet and outlet nozzles. Simulation results were compared with the experimental outcomes obtained in cases of the non-uniform natural inflow of both mediums and to the computation results for a case of the uniform media inflow. The results obtained in this work confirm the significant deterioration of the thermal efficiency of heat exchangers caused by a non-uniform media inflow (by as much as 18.5% compared to the case of a uniform media inflow) which is compliant with other numerous works. The control of the water flow through the individual heat exchanger tubes enables the improvement of thermal efficiency by 4.5% to 18.6% compared to the device with uncontrolled inflow of working fluids, which for some of the analyzed cases is even better than a completely uniform inflow of heat carriers.References
[1] Chiou J.P.: Thermal performance deterioration in crossflow heat exchanger due to the flow nonuniformity. J. Heat Transf. 100(1978), 4, 580–587.
[2] Ranganayakulu Ch., Seetharamu K.N., Sreevatsan K.V.: The effects of inlet fluid flow nonuniformity on thermal performance and pressure drops in cross-flow platefin compact heat exchangers. Int. J. Heat Mass Trans. 40(1996), 27–38.
[3] Kumar S., Dwivedi R., Singh P.K.: Effect of flow maldistribution on thermal performance of water-cooled minichannel heat sink. In: Advances in Fluid and Thermal Engineering (P. Saha, P.M.V. Subbarao, B.S. Sikarwar, Eds.), 2019, 43–52. doi:10.1007/978-981-13-6416-7_5
[4] Joseph J.: Numerical and experimental study of microchannel performance on flow maldistribution. Micromachines (Basel) 11(2020), 3, 323, doi: 10.3390/mi11030323
[5] Zhang K., Li M.J., He Y. L.: A general and rapid method to evaluate the effect of flow maldistribution on the performance of heat exchangers. Int. J. Therm. Sci. 170(2021), 107152. doi: 10.1016/j.ijthermalsci.2021.107152
[6] T’joen C., Willockx A., Steeman H.-J., De Paepe M.: Performance prediction of compact fin-and-tube heat exchangers in maldistributed airflow. Heat Trans. Eng. 28(2007), 12, 986–996.
[7] Tereda F.A., Srihari N., Sunden B., Das S.K.: Experimental investigation on port-tochannel flow maldistribution in plate heat exchangers. Heat Trans. Eng. 28(2007),5, 435–443.
[8] De Schampheleire S., De Kerpel K., Ameel B., Huisseune H., De Paepe, M.: Thermal analysis of a commercial plate fin heat exchanger with nonuniform inlet flow conditions. Heat Trans. Eng. 37(2016), 17, 1466–1477.
[9] Guo J., Huai X., Cheng K., Cui X., Zhang H.: The effects of nonuniform inlet fluid conditions on crossflow heat exchanger. Int. J. Heat Mass Trans. 120(2017),807–817.
[10] Bury T., Składzień J., Hanuszkiewicz-Drapała M.: Experimental and numerical analyses of a non-uniform agents flow impact on a finned cross-flow heat exchanger effectiveness. In: Proc. 22nd Int. Conf. on Efficiency, Cost, Optimization, Simulation and Environmental Impact of Energy Systems – ECOS 2009, Foz do Iguacu, Parana,31 Aug.–3 Sept. 2009 (on CD).
[11] Bury T., Składzień J., Widziewicz K.: Experimental and numerical analyses of finned cross flow heat exchangers efficiency under non-uniform gas inlet flow conditions. Arch. Thermodyn. 31(2010), 4, 133–144.
[12] Neve R.S., Yan Y.Y.: Enhancement of heat exchanger performance using combined electrohydrodynamic and passive methods. Int. J. Heat Fluid Fl. 17(1996), 4, 403–409.
[13] Coetzee H., Liebenberg L., Meyer J.P.: Heat transfer and pressure drop characteristics of angled spiraling tape inserts in a heat exchanger annulus. Heat Trans. Eng.24(2003), 6, 29–39.
[14] Bury T., Składzień J.: Evaluation of selected methods of mitigation of media flow maldistribution impact in finned cross-flow heat exchangers. Int. J. Thermodyn. 16(2013), 4, 189-195.
[15] Hajabdollahi Z., Hajabdollahi H., Kim K.C.: Estimating the non-uniform air velocity distribution for the optimal design of a heat exchanger. Appl. Therm. Eng.153(2019), 704–714.
[16] Bury T., Hanuszkiewicz-Drapała M.: Numerical and experimental analysis of a tubeand-fin crossflow heat exchanger with controlled non-uniform inflow of media. E3S Web Conf. 323(2021), 00005.
[17] Widziewicz K.: Thermodynamic analysis of a cross-flow heat exchanger considering non-uniformity of working mediums inflow and thermal radiation. PhD thesis, Institute of Thermal Technology, Silesian University of Technology, Gliwice, 2014 (in Polish).
[18] Bury T., Hanuszkiewicz-Drapała M.: Analysis of water flow in a cross-current heat exchanger based on a CFD model. In: Proc. of the 4th Int. Sci. Tech. Conf. on Modern Power Systems and Units, Cracow, 2016, 39–40 (in Polish).
[19] Taler D.: Mathematical modeling and control of plate fin and tube heat exchangers. Energ. Conv. Manag. 96(2015), 452–462.
[20] Węglarz K., Taler D., Taler J.: New non-iterative method for computation of tubular cross-flow heat exchangers. Energy 260(2022), 124955.
[21] Korzeń A., Taler D.: Numerical modelling of rapid decrease in water flow rate in a plate-and-tube heat exchanger. Heat Transf. Eng. 44(2023), 11-12, 1072–1081.
[22] Sunden B.: Computational fluid dynamic in research and design of heat exchangers. Heat Trans. Eng. 28(2007), 11, 898–910.
[23] Bhutta M.M.A., Hayat N., Khan A., Kanwar N.A., Khan S.: CFD applications in various heat exchangers design: a review. Appl. Therm. Eng. 32(2012), 1–12.
[24] Jun S., Puri V.M.: 3D milk-fouling model of plate heat exchangers using computational fluid dynamics. Int. J. Dairy Tech. 58(2005), 4, 214–224.
[25] Ozden E., Tari I.: Shell side CFD analysis of a small shell-and-tube heat exchanger. Energ. Convers. Manage. 51(2010), 5, 1004–1014.
[26] Sheik Ismail L., Ranganayakulu C., Shah R.K.: Numerical study of flow patterns of compact plate-fin heat exchangers and generation of design data for offset and wavy fins. Int. J. Heat Mass Transf. 52(2009), 17–18, 3972–3983.
[27] Lee M.S., Li Z., Ling J., Aute V.: A CFD assisted segmented control volume based heat exchanger model for simulation of air-to-refrigerant heat exchanger with air flow mal-distribution. Appl. Therm. Eng. 131(2018), 230–243.
[28] Bury T., Hanuszkiewicz-Drapała M.: Analysis of a controlled non-uniform liquid inflow impact on cross-flow heat exchanger operation. In: Advances in the Study of Heat and Mass Transfer (D. Butrymowicz, K. Śmierciew, P. Jakończuk, Eds.), Bialystok Univ. Technol., Białystok 2022, 247–255 (in Polish). doi: 10.24427/978-83-67185-30-1
[29] Hanuszkiewicz-Drapała M., Bury T., Widziewicz K.: Numerical model of a crossflow heat exchanger with non-uniform flow of media. J. Power Technol. 93(2013), 5, 295–302.
[30] Bury T., Hanuszkiewicz-Drapała M., Widziewicz K.: The finite difference method and the numerical approach for modeling the maldistribution of the flow of media in tube-and-fin cross-flow heat exchangers. Heat Trans. Eng. 39(2018), 13-14, 1179–1191.
[31] ANSYS INC.: ANSYS Fluent Theory Guide, Canonsburg, 2021.
[32] ANSYS Fluent Tutorial Guide 2023 R1, http://www.ansys.com (accesed 15 Jan. 2023).
